To perform a diesel compression test, use the following procedures.

1.Make sure batteries are completely charged and the engine starter motor is in good working condition.

2.Check cylinder head bolts are tightened to specified torque. (120NM + Rotate to 900).

3.Engine should be warmed up until the coolant temperature reaches 750 C to 850C.

4.High pressure Injector pipes and lines should all be removed.

5.The fuel shut-off solenoid should be disconnected to disable the fuel injection pump ( Rotary )

6.Remove no:1injector and crank the engine for a while to clear the gases from the cylinder.

7.Compression gauge adapter should be installed on the injector mounting hole and connect the compression gauge measurement tool.

8.Engine should be cranked for 3-4 seconds, write down the reading of compression gauge after maintaining the 200 – 300 RPM

9.Steps 7 and 8 should be repeated for the remainder of the other cylinders

Diesel engine compression readings average approximately between 275 psi to 400 psi, depending on the design and compression ratio. Compression levels sholud not vary more than 10 to 15 percent (30 psi to 50 psi). Keep your eye out for variation between cylinders during an engine compression check. If say two cylinders have normal pressure readings and two have low readings, engine performance is reduced. If two cylinders side by side read low, it is pointing to a blown head gasket between these two cylinders. If the compression pressure of a cylinder is reading low for the first few piston strokes and then increases to normal, it indicates that a valve is sticking. Indications of valve troubles by compression test will be confirmed by taking vacuum gauge readings.

Purchase a Diesel Compression Tester Here ( ill put one on our website where they can click here and buy )

Low Fuel Pressure

Low Fuel pressure is where most problems occur for fuel supply. There are two faults that could be causing this, diesel injectors or diesel injector rail not holding the fuel within the system and poor fuel supply to the diesel injectors or diesel injector rail.

You should look at the two faults in three ares:-

* Low pressure supply from the fuel tank to the high pressure pump - vehicles that don't have an electric fuel pump to lift the fuel from the tank to the high pressure pump    rely solely on the high pressure pump to lift the fuel from the diesel tank. Vehicles that do have an electrical fuel pump either in the tank or in the fuel line to aid the high pressure pump the bar between the diesel tank and the high pressure pump should be 2 - 5 bars.

* The pressure to deliver fuel from the high pressure pump to the rail/injectors at cranking is around 200 bars, at idle the pressure should be around 300 bars. When the vehicle is running the pressure ranges from 1200 bar to 2000 bar.

* Once the vehicle has reached the running stage the pressure should be maintained at the relevant pressure.

Here at Diesel Jones we sell electrical fuel pumps so if you would like a quote please click on our live link or alternatively use this contact form and we will get back to you asap

Low Cranking Speed

If your vehicle is turning over slowly, your diesel pump can't generate enough fuel pressure to initialize fuel injection causing hard starting problems. During the colder periods of the year low cranking speed is more common due the battery being flat or faulty. Get a quote on a battery by clicking on the online chat or alternatively use this contact form and we will get back to you asap

Glow Plug or Glow Plug Relay Faulty

Glow plugs are important for cold starting. They are electrically controlled heaters which warm the engine prior to cold starts. Without glow plugs, a diesel engine would not start because the engine needs hot compressed air to ignite injected diesel. If your glow plugs are faulty it will make your vehicle not start, hard to start or when the engine is cold produce white smoke. Get a quote on glow plugs and glow plug relays by clicking on live chat or or alternatively use this contact form and we will get back to you asap

Insufficient Fuel Supply

The most common fault for insufficient fuel supply is that the fuel supply pipes are cracked or bent. The vehicle has an empty fuel tank.

Contamination / Fuel Quality

Contamination either by petrol, water or any other foreign matter within the fuel system causes your diesel fuel pump and diesel injectors to fail. The internal parts within the diesel fuel pump and diesel injector get worn and one or a combination of the faults listed above in the trouble shooting chart occurs. If you have had contamination within your fuel system and you have had either your diesel injectors or diesel pump exchanged or repaired you must make sure you completely clean out the fuel system and replace your fuel filter before putting the replacement faulty parts back on to your vehicle. Here at diesel Jones we can analise your fuel for you for £45 + vat, you would receive a print out of the purity of the diesel fuel. We also sell diesel fuel filters if you would like a quote on your diesel injectors, diesel fuel pump or diesel filter click on the live chat link or alternatively use this contact form and we will get back to you asap.

Air - Vacuum in Fuel Supply and Blocked Fuel Supply

Fuel Filters are important part of the diesel fuel injection system. The job of the fuel filter is to remove contaminants from the fuel system before it reaches the diesel injectors or diesel fuel pump. The life of a diesel filter depends on the quality of the fuel that passes through it. Normally the fuel filter would be changed at your annual service. If the diesel fuel filter is blocked before the usual service this indicates that the level of contaminants in the fuel is much higher than normal.

* Water Contamination - Water can enter the fuel tanks through air and at the right ambient temperature condense.

* Petrol Contamination - This is when the wrong fuel is put in your diesel fuel tank at the filling station.

Here at diesel Jones we can Analise your fuel for you for £45 + vat, you would receive a print out of the purity of the diesel fuel. We also sell diesel fuel filters. Click on the live chat link to get a quote or alternatively use this contact form and we will get back to you asap.

Diesel Injector/s Faulty

The biggest result of Common rail diesel injector failure is due to excessive back leak or return flow. The cause of this would be internal worn parts ie your pilot valve, nozzles or seals. The faulty parts allow the fuel to travel back up the injector to the fuel system or diesel tank. The outcome of excessive back leakage is a drop in rail pressure ( see low fuel pressure ) which in-turn results in your vehicle to have hard starting or will not start at all.

Internal worn parts can also cause a delay in the start of injection which results in your vehicle rough running at low RPM or your vehicle to not start at all.

Get a quote on you Diesel Injectors by clicking on the live chat link or alternatively use this contact form and we will get back to you asap.

Not Sure if your diesel injectors are faulty click on the Diesel Injector Testing Form fill in and send the injectors to Diesel Jones and we will test and report back yo you.

Bosch,Delphi,Denso Common Rail Testing Fee £17.63 each

Bosch Unit Injector Testing Fee £52.88 each

Mechanical Injector Testing Free of charge

High Pressure Pump Faulty

If your diesel high pressure fuel pump is faulty this will cause low pressure ( see low fuel pressure ). Normally the fuel pump fails due to internal parts being worn due to contamination ( See Contamination ) or by your fuel pump breaking up internally which causes metal swarf to enter the fuel system. If this happens your injectors will also become faulty and you will need to clean out the whole fuel system before replacing your diesel high pressure pump and injectors. Failure to do so will result in the failure of your diesel high pressure pump and diesel injectors again.

Get a quote on your Diesel High Pressure Pump by clicking on the live chat link or alternatively use this contact form and we will get back to you asap.

Not Sure if your diesel pump is faulty click on the Diesel Pump Testing Form, Fill in and send the fuel pump to us we will test and report back to you.

* Bosch VP30/44 Testing fee £52.88 ( single plug only )

* Bosch High Pressure/Common rail Pump Testing Fee £52.88

* Delphi/Denso Common Rail Pump Testing Fee £141

* Mechanical Fuel Pump Testing Fee £45.00 each

Pressure Regulator / Sensor Faulty

On most vehicles today they have a pressure regulator fitted on the diesel high pressure pump and a sensor on the rail. If either of these go faulty your vehicle will have running issues:-

* Hard Starting

* Uneven tick-over

* Vehicle cutting-out when the RPM is increased

Get a quote on a Pressure Regulator or Rail Sensor by clicking on the live chat link or alternatively use this contact form and we will get back to you asap

Low Pressure Pump Faulty

If your vehicle is fitted with a low pressure pump it can be located on the fuel pipe near the diesel tank or in the diesel tank. If your low pressure pump is faulty you will experience the same symptoms of a high pressure pump.

Get a quote on a Low Pressure Pump by clicking on the live chat link or alternatively use this contact form and we will get back to you asap

Air Intake Restriction

This could be due to your air filter or pipes being blocked. Some vehicles also have a butterfly valve which maybe stuck. In addition the a faulty air flow sensor on the air intake will cause cause excessive black smoke and lack of power.

Turbo Problems

With vehicles being produced with more and more horse power it has been putting a strain on the turbo's in which turbo's failing has become more common. Reasons why turbo's are failing is combination of not allowing the engine to idle when started or switching off, not replacing oil with the manufactures specification oil or poor maintenance.

As your turbo get more and more wear the waste gate sticks causing your vehicle to go into limp mode, smoke excessively or shut down.

If your vehicle has a variable vane turbo and your vehicle carbons up, you would experience black smoke, hesitation on acceleration and also lack of power. A good thing to check is that the sensors and vacuum pipes that operate the turbo are working correctly. Also if you check the air pipes to and from the inlet, inter cooler and turbo as if your clamps are loose or damaged this can also cause the above problems.

EGR Problems

Diesel Injector blow-by Seat leaking

Cam Sensor - Crank sensor

Injector Wiring Harness

Internal Engine Problems

White Smoke

Black Smoke

Blue Smoke